STM32 Programming Adapter Test Socket for LQFP64 QFP64 QFP Package 0.5mm Pitch =STM32-QFP64
Yamaichi IC Test & Burn-in Socket with a simple board, specifically designed for STM32 microcontroller in QFP64(0.5mm pitch) package
Features
- 20-pin JTAG/SWD port and/or 4-pin USART1 interface for programming/testing
- External crystal can be connected via on board socket for system clock
- Onboard 32.768K crystal oscillator
- Two LED indicators for testing, which are connected to the I/O pins via jumpers
- All the MCU pins are accessible on expansion connectors
- pin header pitch: 2.54mm(100mil)
Supported Devices
STM32 microcontroller in QFP64(0.5mm pitch) package with compatible pinouts:
- STM32L1xxR series (STM32L151R8, STM32L152RB, etc.)
- STM32F0xxR series (STM32F051RC, STM32F051RB, etc.)
- STM32F1xxR series (STM32F103RC, STM32F100RB, etc.)
- STM32F2xxR series (STM32F207RC, STM32F215RB, etc.)
- STM32F3xxR series (STM32F303R8, STM32F373RB, etc.)
- STM32F4xxR series (STM32F407RC, STM32F415RB, etc.)
Config the onboard “Device selection jumpers” according to the device to be programmed.
Outline and Dimensions
Unit: mm
Photos
- JTAG/SWD port
- for programming/debugging/testing
- compatible with ST-LINK / J-LINK / ULINK2 / STX-RLINK
- USART1 port
- supports ISP and/or serial port debugging
- LED indicators
- Pin headers connected to MCU pins
- clearly labeled with onboard marks
- easy for testing and further expansion
- Boot mode configuration
- configuring the BOOT0 and BOOT1 via jumpers
- 3.3V onboard regulator
- 5V power input
- External crystal socket
- insert crystal to the holes on two sides, leave alone the middle hole
- Power indicator
- Device selection jumpers
- short the upper headers for STM32F1xx / STM32L1xx / STM32F05x / STM32F3xx
- short the lower headers for STM32F2xx / STM32F4xx
- LED jumpers
- short the jumpers to connect LEDs to MCU I/O pins for testing
- open the jumpers to disconnect
- 32.768K crystal (on bottom side)
- for internal RTC with calibration
JTAG/SWD Connector Layout
The STM32-QFP64 houses JTAG/SWD headers for connecting a programmer. The connector layout is shown in the figure 1 below.
Figure 1. JTAG/SWD connector layout
Boot Mode Configuration
Depending on the used pin configuration, the Flash memory, system memory or SRAM is selected as the boot space, as shown in Table 1 below.
Downloads
Development resources:schematic, etc.
Wiki: www.waveshare.com/wiki/STM32-QFP64
Package Contains
- STM32-QFP64 × 1
- USB power cable × 1
1 
2 
Average Star Rating:
0 out of 5 (0 Ratings)
Feedback Rating for This Product
| Positive (0%) |
5 Stars (0)
|
|
4 Stars (0)
|
|
3 Stars (0)
|
| Neutral (0%) |
2 Stars (0)
|
|
1 Star (0)
|
| Shipping Company |
Shipping Cost |
Estimated Delivery Time |
 |
|
3 - 7 days |
 |
|
3 - 7 days |
 |
|
5 - 14 days |
| Post Air Mail |
Free Shipping |
15 - 45 days |
| Return Policy |
If the product you receive is not as described or low quality, the seller promises that you may return it before order completion (when you click "Confirm Order Received" or exceed confirmation timeframe) and receive a full refund. The return shipping fee will be paid by you. Or, you can choose to keep the product and agree the refund amount directly with the seller.
N.B.: If the seller provides the "Longer Protection" service on this product, you may ask for refund up to 15 days after order completion. |
| Seller Service |
On-time DeliveryIf you do not receive your purchase within 60 days, you can ask for a full refund before order completion (when you click "Confirm Order Received" or exceed confirmation timeframe). |
