US $316.72 US $18.03 US $122.10 US $77.70 US $53.98 US $224.64 US $83.78 US $507.00 US $157.68 US $12.88
No need firmware setting 300M 5.8G Waterproof AP CPE in one Wireless Bridge Access Point Network Repeater for ip camera
● Dial Switch function, Auto match AP, easy to set up. Especially for video surveillance IP camera.
● Support Point-to-Point and Point-to-Multipoint Networking.
● Support Netcheck function: Data analysis, really time signal/traffic monitoring etc.
● Support outdoor temperature：-30°C~65°C, industrial grade design
● Wireless coverage recommended range 3KM
● 5.8Ghz, transmission rate up to 300Mbps
● Build in QUALCOMM AR9344 Chipset, device lower power dissipation and more stable.
● Antenna Polarization: Horizon/Vertical
● Support POE 24V/1A
Easy setting—Dial Switch function
For point-to-point communication, generally a TI-D356H AP is set as transmitter, and the other TI-D356H CPE set as receiver
Note: The frequency of 2 CPE better discrepancy at least 60Mhz,avoid disturbing by same frequency.
2,Point-to- Multipoint Networking
Point to Multipoint ,the wireless bridge set up with transmitter mode in control room ;The cameras connect with wireless bridge set up with receiver mode. The angle of wireless transmitter is directional 60°.
Note: The frequency between adjacent devices to have a difference of 60MHz, to avoid interference with the same frequency.
3,Area multi-camera Transfer
Transfer: When designing the solution and if there is obstacles or blocking , it is recommended to use a group of relay.
The numbers of camera carrying are base on the bandwidth of transmitter side(AP) . The traffic will be increase if the the monitor screen moving.So better reserve 30% balance of bandwidth for using.
A 960P 1.3MP camera 6M bandwidth
A 720P 1.0MP camera 4M bandwidth
A1080P 2.0MP camera 8M bandwidth
A 5.8G 150Mbps wireless bridge has transmission bandwidth about 35Mbps in 2KM outdoor distance with line of sight
A 5.8G 300Mbps wireless bridge has transmission bandwidth about 45Mbps in 2KM outdoor distance with line of sight
When the project install completed . Run the NETCHECK software for 1 to 2 days for performance monitoring .Base on NETCHECK collected information , problems could be troubleshoot and resolved earlier. No after sales service or maintenance needed.
1.When the equipment is power on, there will be electricity in both of the ports. You must use a 4 core cable if the ports are connected to other devices like laptop or switches, otherwise, the connected device will be burnt.
2. POE power supply requires to connect with Category 5 network cable. When connect to the 24V POE, network cable needs to be shorter than 50 meters, when to 48V POE, network cable needs shorter than 80 meters.
Notice: Wireless bridge only support 12V-24V power, if more than 24V, it may be burnt.
5 Stars (0)
4 Stars (0)
3 Stars (0)
2 Stars (0)
1 Star (0)
|Shipping Company||Shipping Cost||Estimated Delivery Time|
|3 - 7 days|
|3 - 7 days|
|5 - 14 days|
|Post Air Mail||Free Shipping||15 - 45 days|
|Return Policy||If the product you receive is not as described or low quality, the seller promises that you may return it before order completion (when you click "Confirm Order Received" or exceed confirmation timeframe) and receive a full refund. The return shipping fee will be paid by you. Or, you can choose to keep the product and agree the refund amount directly with the seller.
N.B.: If the seller provides the "Longer Protection" service on this product, you may ask for refund up to 15 days after order completion.
|Seller Service||On-time DeliveryIf you do not receive your purchase within 60 days, you can ask for a full refund before order completion (when you click "Confirm Order Received" or exceed confirmation timeframe).|